China OEM Supply P22 Alloy Steel Pipe - Seamless Alloy Steel Boiler Pipes Superheater alloy pipes Heat Exchanger Tubes – Sanonpipe Manufacturer and Supplier

OEM Supply P22 Alloy Steel Pipe - Seamless Alloy Steel Boiler Pipes Superheater alloy pipes Heat Exchanger Tubes – Sanonpipe

Short Description:

Product Detail

Product Tags

Feedback (2)

Our advantages are lower prices,dynamic sales team,specialized QC,strong factories,high quality products and services for seamless alloy steel pipe , P91 Alloy Steel Pipe Manufacturer , Boiler Pipes , We are looking forward to cooperating with all customers from at home and abroad. Moreover, customer satisfaction is our eternal pursuit.

OEM Supply P22 Alloy Steel Pipe - Seamless Alloy Steel Boiler Pipes Superheater alloy pipes Heat Exchanger Tubes – Sanonpipe Detail:

Overview

Application

It is mainly used to make high-quality alloy steel pipe for high pressure boiler pipe, heat exchanger pipe and super heat pipe

Main Grade

Grade of high-quality Alloy steel: T2,T12,T11,T22, T91, T92 etc.

Chemical Component

Steel Grade	Chemical Composition%
	C	Si	Mn	P, S Max	Cr	Mo	Ni Max	V	Al Max	W	B
T2	0.10~0.20	0.10~0.30	0.30~0.61	0.025	0.50~0.81	0.44~0.65	–	–	–	–	–
T11	0.05~0.15	0.50~1.00	0.30~0.60	0.025	1.00~1.50	0.44~0.65	–	–	–	–	–
T12	0.05~0.15	Max 0.5	0.30~0.61	0.025	0.80~1.25	0.44~0.65	–	–	–	–	–
T22	0.05~0.15	Max 0.5	0.30~0.60	0.025	1.90~2.60	0.87~1.13	–	–	–	–	–
T91	0.07~0.14	0.20~0.50	0.30~0.60	0.02	8.0~9.5	0.85~1.05	0.4	0.18~0.25	0.015	–	–
T92	0.07~0.13	Max 0.5	0.30~0.60	0.02	8.5~9.5	0.30~0.60	0.4	0.15~0.25	0.015	1.50~2.00	0.001~0.006

For T91 other than above also includes Nickel 0.4, Va 0.18-0.25, Ni 0.06-0.10, Ni 0.03-0.07, Al 0.02, Ti 0.01, Zr 0.01. A Maximum, unless range or minimum is indicated. Where ellipses (…) appear in this table, there is no requirement, and analysis for the element need not be determined or reported. B It is permissible to order T2 and T12 with a sulfur content of 0.045 max. C Alternatively, in lieu of this ratio minimum, the material shall have a minimum hardness of 275 HV in the hardened condition, defined as after austenitizing and cooling to room temperature but prior to tempering. Hardness testing shall be performed at mid-thickness of the product. Hardness test frequency shall be two samples of product per heat treatment lot and the hardness testing results shall be reported on the material test report.

Mechanical Property

Steel Grade	Mechanical Properties
Steel Grade	T. S	Y. P	Elongation	Hardness
T2	≥ 415MPa	≥ 205MPa	≥ 30%	163HBW(85HRB)
T11	≥ 415MPa	≥ 205MPa	≥ 30%	163HBW(85HRB)
T12	≥ 415MPa	≥ 220MPa	≥ 30%	163HBW(85HRB)
T22	≥ 415MPa	≥ 205MPa	≥ 30%	163HBW(85HRB)
T91	≥ 585MPa	≥ 415MPa	≥ 20%	250HBW(25HRB)
T92	≥ 620MPa	≥ 440MPa	≥ 20%	250HBW(25HRB)

Tolerance

Permitted Variations in Wall thickness

Wallthickess %
outside diameter in. mm	0.095 2.4 and under	over0.095 to 0.15 2.4-3.8 incl.	over 0.15 to 0.18 3.8-4.6 incl	over 0.18 to 4.6
over under over under over under over under
seamless, hot finished
4inch and under 40 0 35 0 33 0 28 0
over 4 inch .. .. 35 0 33 0 28 0
seamless, cold finished
		over under
11/2 and under		20 0
over 11/2		22 0

The permitted variations in wall thickness apply only to tube , except internal-upset tubes, as rolled or cold finished

and before swaging,expanding ,bending,polishing,or other fabricating operations

Permitted Variations in Outside Diameter

outside diameter （mm)	Pemitted Variation( mm)
hot finished seamless tube	over	under
4″ (100mm)and under	0.4	0.8
4-71/2″(100-200mm）	0.4	1.2
71/2-9“（200-225）	0.4	1.6
Welded tubes and cold finished seamless tubes
under1″(25mm)	0.1	0.11
1-11/2″(25-40mm)	0.15	0.15
11/2-2″(40-50mm)	0.2	0.2
2-21/2″(50-65mm)	0.25	0.25
21/2-3″(65-75mm)	0.3	0.3
3-4″(75-100mm)	0.38	0.38
4-71/2″(100-200mm）	0.38	0.64
71/2-9“（200-225）	0.38	1.14

Test Requirement

Hydraustatic Test:

The Steel Pipe Should Be Tested Hydraulically One By One. The Maximum Test Pressure Is 20 MPa. Under The Test Pressure, The Stabilization Time Should Be Not Less Than 10 S, And The Steel Pipe Should Not Leak. Or The Hydraulic Test Can Be Replaced By Eddy Current Testing Or Magnetic Flux Leakage Testing.

Nondestructive Test：

Pipes That Require More Inspection Should Be Ultrasonically Inspected One By One. After The Negotiation Requires The Consent Of The Party And Is Specified In The Contract, Other Non-Destructive Testing Can Be Added.

Flattening Test：

Tubes With An Outer Diameter Greater Than 22 Mm Shall Be Subjected To A Flattening Test. No Visible Delamination, White Spots, Or Impurities Should Occur During The Entire Experiment.

Hardness Test:

For Pipe Of Grades P91, P92, P122, And P911, Brinell, Vickers, Or Rockwell Hardness Tests Shall Be Made On A Specimen From Each Lot

Product Detail

Boiler Tube

GB/T5310-2017

ASME SA-106/SA-106M-2015

ASTMA210(A210M)-2012

ASME SA-213/SA-213M

ASTM A335/A335M-2018

Product detail pictures:

Related Product Guide:

To create far more benefit for customers is our company philosophy; customer growing is our working chase for OEM Supply P22 Alloy Steel Pipe - Seamless Alloy Steel Boiler Pipes Superheater alloy pipes Heat Exchanger Tubes – Sanonpipe , The product will supply to all over the world, such as: Bandung , Kuwait , Nepal , We focus on providing service for our clients as a key element in strengthening our long-term relationships. Our continual availability of high grade products in combination with our excellent pre-sale and after-sales service ensures strong competitiveness in an increasingly globalized market. We are willing to cooperate with business friends from at home and abroad and create a great future together.

Alloy Mechanics Pipe